新聞資訊
聯絡我們

濟南九創門業有限公司
聯絡人│✘│:李經理
電話│✘│:15006519345
網址:www.zjfhby.com
地址│✘│:濟南市天橋區北園大街372號大明家居3F-A-10
捲簾門配件一定要定期檢查
來源│✘│:http://www.jnhsjlm.com 日期│✘│:2022-12-29 釋出人│✘│:guanli
濟南捲簾為什麼說一定要定期檢查捲簾門配件呢·✘││·?下面↟✘•▩•,小編來給大家講解一下↟☁▩☁·。
Why does Jinan roller shutter say that the accessories of roller shutter must be checked regularly? Now, let's talk about it.
1.定期檢查門體活動部分↟✘•▩•,保證執行不會受阻↟✘•▩•,保持潤滑↟✘•▩•,執行聲音正常↟✘•▩•,否則有可能造成人身安全和影響使用壽命↟☁▩☁·。
1. Regularly check the moving parts of the door body to ensure that the operation is not blocked, lubrication is maintained, and the operating sound is normal, otherwise it may cause personal safety and affect the service life.
2.卷門機應由人員安裝◕₪✘•↟、維護↟✘•▩•,必須有良好的保護接地↟✘•▩•,否則有可能造成人身安全;
2. The rolling door machine shall be installed and maintained by professionals, and must be well grounded, otherwise it may cause personal safety;
3.卷門機執行時↟✘•▩•,門下嚴禁站立或通行↟✘•▩•,門簾下方不得有阻礙物;
3. When the door roller is running, it is strictly forbidden to stand or pass under the door, and there shall be no obstacles under the curtain;
4.傳動鏈條調整│✘│:先調松支架板上小鏈輪的固定螺栓M6↟✘•▩•,再調整卷門機變速箱上的2只螺栓M8↟✘•▩•,使傳動鏈條下垂度為3-6mm(未裝門簾前調整)↟✘•▩•,再鎖緊3只支腳螺母M10.
4. Adjustment of drive chain: first loosen the fixing bolt M6 of the small sprocket on the support plate, then adjust the two bolts M8 on the gearbox of the door roller to make the drive chain sag 3-6mm (adjust before installing the door curtain), and then tighten the three foot nuts M10
5.本產品按右安裝方案製造(從室內朝門外看)↟✘•▩•,若需左安裝↟✘•▩•,應將制動殼體上4只螺釘M5旋鬆↟✘•▩•,再旋轉殼體180°後重新平衡鎖緊↟✘•▩•,並把按鈕開關上白◕₪✘•↟、綠色線對調連線;
5. The product is manufactured according to the right installation scheme (looking from the indoor to the outdoor). If it needs to be installed on the left, loosen the four screws M5 on the brake housing, rotate the housing 180 °, then re balance and lock it, and switch the white and green lines on the button switch;
6.卷門機應水平安裝↟✘•▩•,卷軸應水平◕₪✘•↟、同心↟✘•▩•,門簾升降無滯卡;
6. The door winder shall be installed horizontally, the reel shall be horizontal and concentric, and the door curtain shall be lifted without stagnation;
7.捲簾門的上下行程調整│✘│:試機前先擰鬆限位滑塊上的2只緊定螺釘↟✘•▩•,把門簾上升至欲定的高度,旋動上行限位螺套觸壓到微動開關↟✘•▩•,聽到“嘀達”聲擰緊螺釘;再把門簾降至地面↟✘•▩•,以相同方法↟☁▩☁·。確定下行限位螺套位置↟✘•▩•,用手指用力擰緊2只緊定螺釘↟☁▩☁·。
7. Adjustment of the up and down travel of the roller shutter: Before the test run, loosen the two set screws on the limit slider, raise the shutter to the desired height, rotate the upper limit screw sleeve to touch and press the microswitch, and tighten the screws with the sound of "ticking"; Then lower the curtain to the ground in the same way. Determine the position of the lower limit screw sleeve, and tighten 2 set screws with fingers.
門是現在許多大型商場或者車庫所需要安裝的一種門↟✘•▩•,既開關方便↟✘•▩•,又節省空間↟✘•▩•,因此應用的比較廣泛↟✘•▩•,在生活中很多地方都能見到↟☁▩☁·。那麼自己想動手安裝捲簾門該如何操作?捲簾門安裝方式又有哪些呢?濟南捲簾門一般有中裝◕₪✘•↟、內裝◕₪✘•↟、外裝三種安裝方式↟✘•▩•,不同的安裝方式有不同的配置需求↟✘•▩•,也有各自的優勢與劣勢↟✘•▩•,要根據現場環境和客戶的具體要求選擇合適的安裝方式↟☁▩☁·。
The door is a kind of door that needs to be installed in many large shopping malls or garages. It is convenient to open and close and saves space. Therefore, it is widely used and can be seen in many places of life. How to install the roller shutter door yourself? What are the installation methods of rolling shutter doors? Jinan roller shutter doors generally have three installation methods: medium decoration, interior decoration and exterior decoration. Different installation methods have different configuration requirements, as well as their own advantages and disadvantages. The appropriate installation method should be selected according to the site environment and the specific requirements of customers.

1◕₪✘•↟、中裝│✘│:將捲簾門窗安裝在建築物預留的洞口內
1. Medium decoration: install rolling shutter doors and windows in the reserved opening of the building
2◕₪✘•↟、內裝│✘│:將捲簾門窗貼裝在建築物預留洞口內牆面
2. Interior decoration: stick the rolling shutter doors and windows on the interior wall of the reserved opening of the building
3◕₪✘•↟、外裝│✘│:將濟南捲簾門窗貼裝在建築物預留洞口外牆面
3. Exterior decoration: stick Jinan roller shutter doors and windows on the exterior wall of the reserved opening of the building
濟南捲簾門的安裝步驟│✘│:
Installation steps of Jinan roller shutter door:
1◕₪✘•↟、確定安裝捲簾門的位置↟✘•▩•,並用線墜◕₪✘•↟、水平尺等工具進行標註↟✘•▩•,找準水平線和垂直線↟☁▩☁·。
1. Determine the installation position of roller shutter door, mark it with plumb bob, level ruler and other tools, and align the horizontal line and vertical line.
2◕₪✘•↟、根據定位的劃線開始安裝捲簾門的邊框↟☁▩☁·。
2. Start to install the frame of the roller shutter door according to the positioning line.
3◕₪✘•↟、根據卷門機的說明書所提示的方法步驟以及注意事項進行卷簾門機的安裝↟☁▩☁·。
3. Install the rolling door machine according to the methods, steps and precautions indicated in the manual of the rolling door machine.
4◕₪✘•↟、將組裝好的捲簾門體固定好↟✘•▩•,然後將限位器找準位置裝上↟✘•▩•,並試著運轉↟☁▩☁·。進行滑道◕₪✘•↟、手動機構◕₪✘•↟、包箱的安裝↟☁▩☁·。
4. Fix the assembled roller shutter door body, then install the limiter at the correct position, and try to run it. Install the slideway, manual mechanism and box.
Why does Jinan roller shutter say that the accessories of roller shutter must be checked regularly? Now, let's talk about it.
1.定期檢查門體活動部分↟✘•▩•,保證執行不會受阻↟✘•▩•,保持潤滑↟✘•▩•,執行聲音正常↟✘•▩•,否則有可能造成人身安全和影響使用壽命↟☁▩☁·。
1. Regularly check the moving parts of the door body to ensure that the operation is not blocked, lubrication is maintained, and the operating sound is normal, otherwise it may cause personal safety and affect the service life.
2.卷門機應由人員安裝◕₪✘•↟、維護↟✘•▩•,必須有良好的保護接地↟✘•▩•,否則有可能造成人身安全;
2. The rolling door machine shall be installed and maintained by professionals, and must be well grounded, otherwise it may cause personal safety;
3.卷門機執行時↟✘•▩•,門下嚴禁站立或通行↟✘•▩•,門簾下方不得有阻礙物;
3. When the door roller is running, it is strictly forbidden to stand or pass under the door, and there shall be no obstacles under the curtain;
4.傳動鏈條調整│✘│:先調松支架板上小鏈輪的固定螺栓M6↟✘•▩•,再調整卷門機變速箱上的2只螺栓M8↟✘•▩•,使傳動鏈條下垂度為3-6mm(未裝門簾前調整)↟✘•▩•,再鎖緊3只支腳螺母M10.
4. Adjustment of drive chain: first loosen the fixing bolt M6 of the small sprocket on the support plate, then adjust the two bolts M8 on the gearbox of the door roller to make the drive chain sag 3-6mm (adjust before installing the door curtain), and then tighten the three foot nuts M10
5.本產品按右安裝方案製造(從室內朝門外看)↟✘•▩•,若需左安裝↟✘•▩•,應將制動殼體上4只螺釘M5旋鬆↟✘•▩•,再旋轉殼體180°後重新平衡鎖緊↟✘•▩•,並把按鈕開關上白◕₪✘•↟、綠色線對調連線;
5. The product is manufactured according to the right installation scheme (looking from the indoor to the outdoor). If it needs to be installed on the left, loosen the four screws M5 on the brake housing, rotate the housing 180 °, then re balance and lock it, and switch the white and green lines on the button switch;
6.卷門機應水平安裝↟✘•▩•,卷軸應水平◕₪✘•↟、同心↟✘•▩•,門簾升降無滯卡;
6. The door winder shall be installed horizontally, the reel shall be horizontal and concentric, and the door curtain shall be lifted without stagnation;
7.捲簾門的上下行程調整│✘│:試機前先擰鬆限位滑塊上的2只緊定螺釘↟✘•▩•,把門簾上升至欲定的高度,旋動上行限位螺套觸壓到微動開關↟✘•▩•,聽到“嘀達”聲擰緊螺釘;再把門簾降至地面↟✘•▩•,以相同方法↟☁▩☁·。確定下行限位螺套位置↟✘•▩•,用手指用力擰緊2只緊定螺釘↟☁▩☁·。
7. Adjustment of the up and down travel of the roller shutter: Before the test run, loosen the two set screws on the limit slider, raise the shutter to the desired height, rotate the upper limit screw sleeve to touch and press the microswitch, and tighten the screws with the sound of "ticking"; Then lower the curtain to the ground in the same way. Determine the position of the lower limit screw sleeve, and tighten 2 set screws with fingers.
門是現在許多大型商場或者車庫所需要安裝的一種門↟✘•▩•,既開關方便↟✘•▩•,又節省空間↟✘•▩•,因此應用的比較廣泛↟✘•▩•,在生活中很多地方都能見到↟☁▩☁·。那麼自己想動手安裝捲簾門該如何操作?捲簾門安裝方式又有哪些呢?濟南捲簾門一般有中裝◕₪✘•↟、內裝◕₪✘•↟、外裝三種安裝方式↟✘•▩•,不同的安裝方式有不同的配置需求↟✘•▩•,也有各自的優勢與劣勢↟✘•▩•,要根據現場環境和客戶的具體要求選擇合適的安裝方式↟☁▩☁·。
The door is a kind of door that needs to be installed in many large shopping malls or garages. It is convenient to open and close and saves space. Therefore, it is widely used and can be seen in many places of life. How to install the roller shutter door yourself? What are the installation methods of rolling shutter doors? Jinan roller shutter doors generally have three installation methods: medium decoration, interior decoration and exterior decoration. Different installation methods have different configuration requirements, as well as their own advantages and disadvantages. The appropriate installation method should be selected according to the site environment and the specific requirements of customers.

1◕₪✘•↟、中裝│✘│:將捲簾門窗安裝在建築物預留的洞口內
1. Medium decoration: install rolling shutter doors and windows in the reserved opening of the building
2◕₪✘•↟、內裝│✘│:將捲簾門窗貼裝在建築物預留洞口內牆面
2. Interior decoration: stick the rolling shutter doors and windows on the interior wall of the reserved opening of the building
3◕₪✘•↟、外裝│✘│:將濟南捲簾門窗貼裝在建築物預留洞口外牆面
3. Exterior decoration: stick Jinan roller shutter doors and windows on the exterior wall of the reserved opening of the building
濟南捲簾門的安裝步驟│✘│:
Installation steps of Jinan roller shutter door:
1◕₪✘•↟、確定安裝捲簾門的位置↟✘•▩•,並用線墜◕₪✘•↟、水平尺等工具進行標註↟✘•▩•,找準水平線和垂直線↟☁▩☁·。
1. Determine the installation position of roller shutter door, mark it with plumb bob, level ruler and other tools, and align the horizontal line and vertical line.
2◕₪✘•↟、根據定位的劃線開始安裝捲簾門的邊框↟☁▩☁·。
2. Start to install the frame of the roller shutter door according to the positioning line.
3◕₪✘•↟、根據卷門機的說明書所提示的方法步驟以及注意事項進行卷簾門機的安裝↟☁▩☁·。
3. Install the rolling door machine according to the methods, steps and precautions indicated in the manual of the rolling door machine.
4◕₪✘•↟、將組裝好的捲簾門體固定好↟✘•▩•,然後將限位器找準位置裝上↟✘•▩•,並試著運轉↟☁▩☁·。進行滑道◕₪✘•↟、手動機構◕₪✘•↟、包箱的安裝↟☁▩☁·。
4. Fix the assembled roller shutter door body, then install the limiter at the correct position, and try to run it. Install the slideway, manual mechanism and box.
下一篇│✘│:車庫門的適用範圍都有哪些地方·✘││·? 上一篇│✘│:濟南捲簾門安裝簡便還節省空間
推薦閱讀/ Recommended reading
- 車庫門的選擇要注意什麼·✘││·? 2023-01-30
- 車庫門和電機的保養要注意哪些·✘││·? 2023-01-24
- 寒冷地區車庫門的保養要注意什麼·✘││·? 2023-01-18
- 快速捲簾門常見故障及如何維修 2023-01-13
快速捲簾門的使用場所有哪些·✘││·?
[2018-08-23]
快速門重要的特點↟✘•▩•,就是啟閉速度快↟✘•▩•,這樣可以有效的提高工廠的工作效率↟✘•▩•,隔絕氣流↟✘•▩•,防塵↟✘•▩•,密封↟✘•▩•,保溫等各種優點不勝列舉↟☁▩☁·。今天我為大家舉一